Configured for interface functions within ABB ACS6000 drive equipment, the ABB UF C760 BE 142 3BHE004573R0142 (UFC760BE142 Interface Board) provides the physical interface hardware identified by ABB for the ACS6000 platform. ABB identifies the part as an interface board and lists it as an ACS6000 spare part.

Model Identification

ABB product records identify 3BHE004573R0142 as "UF C760 BE142; INTERFACE BOARD", with a net weight of 0.54 kg and a minimum order quantity of 1 piece. The ABB record also associates the part with ACS6000 equipment.

Industrial Control Interface Characteristics

The UF C760 BE142 interface board is associated with ABB ACS6000 medium-voltage drive equipment. Its documented product classification is an interface board rather than a general-purpose PLC I/O module. Therefore, the board should be matched against the installed ACS6000 hardware configuration before replacement.

For ABB industrial control hardware, interface-board replacement also requires attention to firmware and hardware compatibility. A physically matching PCB should not be assumed to provide functional interchangeability unless the applicable ACS6000 configuration confirms the replacement relationship.

The supplied data lists 24 VDC +/-15%, configurable digital channels, optional analog signal ranges, and electrical isolation. These values are retained as supplied specifications and are not presented as independently verified ABB catalog parameters.

Ordering Information

• 1 x ABB UF C760 BE142 Interface Board
• Part number: 3BHE004573R0142
• Product type: Interface Board
• Manufacturer: ABB
• Application reference: ACS6000
• No separate installation kit is identified in the supplied product information.
• Connector sets, mounting hardware, and accessories should be verified against the specific ACS6000 equipment configuration.

Installation and Handling

Board Identification

• Confirm the installed board marking before removal.
• Match the replacement part number with 3BHE004573R0142.
• Check the ABB Type Designation for UF C760 BE142.
• Verify the target ACS6000 equipment configuration before installation.

Electrical Handling

• Isolate the associated drive equipment before accessing the PCB.
• Follow the equipment manufacturer's discharge and electrical isolation procedures.
• Use appropriate ESD protection when handling the circuit board.
• Do not connect or disconnect board wiring while energized unless the applicable ABB equipment documentation explicitly permits the operation.

Wiring and Shielding

• Route signal wiring separately from high-current power conductors.
• Maintain existing shield termination practices used by the ACS6000 installation.
• Avoid unnecessary parallel routing with switching and motor power cables.
• Inspect connectors and PCB interfaces for contamination, mechanical damage, or oxidation before installation.

Frequently Asked Questions

• What is the ABB part number?

  The ABB product ID is 3BHE004573R0142. The ABB Type Designation is UF C760 BE142.

• What is the product type?

  ABB classifies 3BHE004573R0142 as an INTERFACE BOARD. It is listed as a spare part associated with ACS6000 equipment.

• What is the net weight?

  The verified ABB product record specifies a product net weight of 0.54 kg. A separate 0.36 kg figure appears in secondary listings and should not replace the ABB value.

• Is this a general PLC analog input module?

  No. ABB identifies the component as an interface board for ACS6000 equipment. It should not be treated as a generic PLC I/O module without configuration verification.

• What ACS6000 equipment is associated with this board?

  ABB-related product records identify the part as a spare component for ACS6000 equipment. The exact installation position should be checked against the drive documentation.

• Is power consumption specified?

  The verified ABB product record does not state a power-consumption value. Therefore, a numerical consumption figure should not be assumed for this interface board.

• Can the board be replaced while the system is energized?

  No hot-swap capability is established by the supplied data or verified product record. The associated drive should be electrically isolated according to its applicable service procedure.

• Does the part number identify the complete interface board?

  Yes. ABB identifies 3BHE004573R0142 as the product ID for UF C760 BE142, with the catalog description "INTERFACE BOARD."