{"product_id":"cs1w-scb41-v1-omron-serial-communication-board-cs1","title":"CS1W-SCB41-V1 Omron Serial Communication Board CS1","description":"\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eThe \u003cstrong\u003eOmron CS1W-SCB41-V1\u003c\/strong\u003e, also cataloged as the \u003cstrong\u003eCS1W-SCB41-V1\u003c\/strong\u003e Serial Communication Board, operates as a dedicated hardware component for serial protocol conversion and data framing within SYSMAC CS1 CPU units.\u003c\/p\u003e\n\u003ch3\u003ePart Number Nomenclature\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCS1W Subsystem Identifier\u003c\/strong\u003e: Specifies internal CPU slot option board compatibility designed exclusively for CS1 architecture.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSCB Serial Class\u003c\/strong\u003e: Identifies direct-bus serial communication interface board hardware.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e41 Port Configuration\u003c\/strong\u003e: Indicates 1 x RS-232C port plus 1 x RS-422\/485 serial port layout.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eV1 Version Designation\u003c\/strong\u003e: Denotes updated hardware revision supporting protocol macro execution and enhanced baud rate control.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eHardware Technical Parameters\u003c\/h3\u003e\n\u003cfigure\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/th\u003e\n\u003cth\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eCS1W-SCB41-V1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eOmron\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eJapan\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003e1.5 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShipping Dimensions\u003c\/td\u003e\n\u003ctd\u003e15.0 x 13.0 x 4.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e0 to +55 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003e0.28 A at 5 VDC (internal CPU bus)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePort 1 Interface\u003c\/td\u003e\n\u003ctd\u003eRS-232C (D-Sub 9-pin female)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePort 2 Interface\u003c\/td\u003e\n\u003ctd\u003eRS-422\/485 (Terminal block connector)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCommunications Functions\u003c\/td\u003e\n\u003ctd\u003eProtocol macro, Host Link, 1:N NT Link, Modbus-RTU slave, Serial Gateway\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003c\/figure\u003e\n\u003ch3\u003eBackplane Synchronization and Execution Dynamics\u003c\/h3\u003e\n\u003cp\u003eThe board processes custom serial framing routines directly on its integrated processor, maintaining internal CPU backplane bus communication velocity during intensive serial data exchange. High firmware flash compatibility allows seamless synchronization with CPU execution cycles, enabling high-density field network routing without increasing main program scan latencies during multi-port serial execution.\u003c\/p\u003e\n\u003ch3\u003eOrder Package Contents\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e1 x Omron CS1W-SCB41-V1 Serial Communication Board\u003c\/li\u003e\n\u003cli\u003e1 x RS-422\/485 Terminal Block Connector\u003c\/li\u003e\n\u003cli\u003e2 x Board Retention Screws\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCabinet Assembly and Mounting Procedures\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePower Interruption Rule\u003c\/strong\u003e: Completely isolate main power to the CPU rack before removing the CPU option slot cover and seating the board.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBoard Alignment\u003c\/strong\u003e: Insert the board straight into the internal CPU connector and tighten both mounting screws to secure mechanical ground.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShield Grounding\u003c\/strong\u003e: Connect cable shields to the connector ground shells or earth terminal to mitigate differential-mode noise interference.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTerminating Resistor\u003c\/strong\u003e: Set the physical RS-422\/485 DIP switch to ON at both end-nodes of a multi-drop network segment.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eTechnical FAQ\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003eCan the CS1W-SCB41-V1 board be installed or replaced while the CPU rack is powered?\u003c\/p\u003e\n\u003cp\u003eNo, the option board must be installed or removed only when the CPU power supply is fully de-energized to prevent circuit damage.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWhat supplies the electrical operating power for the option board?\u003c\/p\u003e\n\u003cp\u003eOperating current of 0.28 A is drawn directly from the 5 VDC internal logic rail supplied via the CPU backplane interface.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eCan the RS-232C and RS-422\/485 ports operate independently at different baud rates?\u003c\/p\u003e\n\u003cp\u003eYes, both ports can be independently configured for distinct communication protocols, frame formats, and baud rates.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWhat protocol mode enables custom third-party serial messaging?\u003c\/p\u003e\n\u003cp\u003eThe Protocol Macro function allows custom ASCII or binary message frames to be created using CX-Protocol and executed by the board.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eHow are node addresses set for multi-drop RS-485 configurations?\u003c\/p\u003e\n\u003cp\u003eNode unit numbers are defined via CPU memory allocated settings or software parameters, depending on the selected protocol mode.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWhat is the maximum transmission distance for the RS-422\/485 port?\u003c\/p\u003e\n\u003cp\u003eThe maximum cumulative cable length for the RS-422\/485 network line is 500 m when using approved shielded twisted-pair wire.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eWhat status does the COMM LED indicate during field operation?\u003c\/p\u003e\n\u003cp\u003eFlashing COMM LEDs indicate active data transmission (TX) or reception (RX) activity on the respective serial communication port.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003eHow is two-wire versus four-wire mode configured on the RS-422\/485 port?\u003c\/p\u003e\n\u003cp\u003eOperational mode is selected via the onboard hardware slide switch located near the RS-422\/485 terminal connector block.\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Omron","offers":[{"title":"Default Title","offer_id":47306597400749,"sku":"CS1W-SCB41-V1","price":242.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0733\/1613\/9181\/files\/omron_cs1w-scb41-v1_4.jpg?v=1789451081","url":"https:\/\/www.maxwellplc.com\/products\/cs1w-scb41-v1-omron-serial-communication-board-cs1","provider":"Maxwell PLC Ltd","version":"1.0","type":"link"}