{"product_id":"bently-nevada-330425-02-cn-piezoelectric-accelerometer-acceleration-transducer","title":"Bently Nevada 330425-02-CN Piezoelectric Accelerometer Acceleration Transducer","description":"\u003ch2\u003eProduct Overview\u003c\/h2\u003e\n\u003cp\u003eThe Bently Nevada 330425-02-CN Accelerometer Transducer delivers critical high-frequency vibration telemetry required for heavy-duty industrial rotating machinery protection. This premium piezoelectric acceleration sensor measures structural casing vibration, detecting structural anomalies, rolling element bearing degradation, and gear mesh defects that standard low-frequency proximity probes might miss.\u003c\/p\u003e\n\u003cp\u003eReliability engineers install this high-g acceleration transducer within comprehensive Turbine Supervisory Instrumentation (TSI) setups to safeguard high-capital infrastructure, such as gas turbine casings, high-speed gearboxes, and large induction motor frames. The internal piezoceramic sensing element generates an exceptionally clean, low-noise analog signal. This data streams directly to centralized monitoring platforms or automated machinery protection networks, enabling emergency shutdown interlocks to respond instantly to severe mechanical stress and prevent catastrophic component destruction.\u003c\/p\u003e\n\u003ch2\u003ePart Number Structural Identification\u003c\/h2\u003e\n\u003ch3\u003e330425 [330400 Series High-Performance Accelerometer Base]\u003c\/h3\u003e\n\u003cp\u003eSpecifies a ruggedized piezoelectric accelerometer housing utilizing a top-exit connector layout, engineered specifically to measure high-frequency casing vibration with minimum cross-axis sensitivity.\u003c\/p\u003e\n\u003ch3\u003e-02 [Mounting Thread Option]\u003c\/h3\u003e\n\u003cp\u003eDesignates a 1\/4-28 UNF imperial threaded mounting stud configuration, providing standard physical attachment to flat, tapped structural surfaces across Western machinery frames.\u003c\/p\u003e\n\u003ch3\u003e-CN [Regional Explosive Area Authorization]\u003c\/h3\u003e\n\u003cp\u003eCertifies the complete sensor assembly under local hazardous area frameworks, ensuring full intrinsic safety and explosion-proof regulatory compliance when deployed within zoned industrial areas.\u003c\/p\u003e\n\u003ch3\u003eHermetic Laser Welds\u003c\/h3\u003e\n\u003cp\u003eEmploys an absolute laser-sealed 316L stainless steel enclosure design that physically isolates the delicate internal crystalline structure from outside contamination or fluid ingress.\u003c\/p\u003e\n\u003ch2\u003eMechanical Dimensions \u0026amp; Performance Layout\u003c\/h2\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003ctd\u003e\u003cstrong\u003eParameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cstrong\u003eCertified Technical Specification Data\u003c\/strong\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eManufacturer\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eBently Nevada (Baker Hughes)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eCountry of Origin\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eUnited States\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eHS Code\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e90318080\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eNet Transmitter Weight\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e0.12 kg (0.26 lbs)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eCase Package Dimensions\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e140 mm x 140 mm x 50 mm (5.5 in x 5.5 in x 2.0 in)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eMeasurement Acceleration Range\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eUp to 490 m\/s² (50 g) peak operating capacity\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eTransducer Scale Factor\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e10.2 mV\/m\/s² (100 mV\/g) ±5% calibrated sensitivity\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eFrequency Response Envelope\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e10 Hz to 15 kHz (600 cpm to 900,000 cpm) ±3 dB window\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eTemperature Operational Limits\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003e-51°C to +121°C (-60°F to +250°F)\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cspan\u003eEnclosure Ingress Protection\u003c\/span\u003e\u003c\/td\u003e\n\u003ctd\u003e\u003cspan\u003eIP68 \/ NEMA 4X hermetically sealed housing\u003c\/span\u003e\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch2\u003eField Torque \u0026amp; Structural Mounting Guidelines\u003c\/h2\u003e\n\u003cp\u003eField instrumentation crews must mount the accelerometer to a perfectly flat, smooth surface to guarantee accurate high-frequency transmission. Clean the surface area to a smooth finish, tap a 1\/4-28 UNF mounting hole perpendicular to the casing, and apply a thin layer of high-temperature silicone grease to the mounting interface to optimize structural signal bridging.\u003c\/p\u003e\n\u003cp\u003eTighten the accelerometer casing to the machine body with a strict installation torque of 4.5 N·m (40 in·lb). Insufficient tightening torque skews high-frequency response data, while over-tightening can permanently damage the internal piezoelectric crystal assembly. Technicians must route the mating cable using a strict minimum bend radius of 50.8 mm (2.0 inches) and secure it to the machine casing with support clips within 150 mm of the sensor body to minimize wire whip and cable noise.\u003c\/p\u003e\n\u003ch2\u003eStress Survivability \u0026amp; Distributed Control Automation Layer\u003c\/h2\u003e\n\u003cp\u003eThe 316L stainless steel construction of the 330425-02-CN allows it to withstand exposure to hot synthetic bearing oils, abrasive dust clouds, and high-pressure caustic washes. The internal electrical circuit features total isolation from the outer housing block, preventing ground loop interference and protecting the integrity of the data stream from heavy plant electrical switching noise.\u003c\/p\u003e\n\u003cp\u003eThe raw analog acceleration signal flows directly into the input cards of a Bently Nevada 3500\/42M monitor or an automated process loop. The system integrates this high-frequency tracking data into plant-wide Honeywell Experion PKS or Siemens S7 PLC networks via dedicated 4-20mA transmitters or Modbus TCP links. This multi-layered layout provides the control room with simultaneous access to split-second safety interlocks and deep predictive machine health trending.\u003c\/p\u003e\n\u003ch2\u003eCommercial Packing Inventory\u003c\/h2\u003e\n\u003cp\u003eThe factory-sealed individual carton contains the following tracking items:\u003c\/p\u003e\n\u003cp\u003e(1) Original Bently Nevada 330425-02-CN Piezoelectric Accelerometer Transducer\u003c\/p\u003e\n\u003cp\u003e(2) Factory-certified 1\/4-28 UNF mounting stud insert\u003c\/p\u003e\n\u003cp\u003e(3) Premium silicone fluid-sealing interface washer\u003c\/p\u003e\n\u003cp\u003e(4) Complete material traceability card and individual physical calibration report\u003c\/p\u003e\n\u003ch2\u003ePremium Freight \u0026amp; Dispatch Logistics\u003c\/h2\u003e\n\u003cp\u003eOur global supply center processes and dispatches all equipment inventory within 2-7 days following payment finalization. We route all critical machinery components via premium express air carriers, including DHL, FedEx, and UPS, to guarantee fast, tracked, and insured delivery to your facility.\u003c\/p\u003e\n\u003cp\u003eOur warehouse packages each accelerometer assembly inside heavy-duty anti-static industrial packaging sheets before securing it within custom, shock-absorbing foam padding inserts. This strict packaging process provides full protection against electrostatic discharge, heavy transit vibrations, and ambient moisture entry along international shipping routes.\u003c\/p\u003e\n\u003ch2\u003eField Maintenance Engineering FAQ\u003c\/h2\u003e\n\u003ch3\u003eQ1: Can I route this accelerometer signal directly into a standard 24V PLC analog input card?\u003c\/h3\u003e\n\u003cp\u003eA1: No. Piezoelectric accelerometers require specialized constant-current power sourcing (typically provided by an external charge amplifier, a vibration transmitter monitor, or a Bently Nevada 3500\/42M card). Direct connection to a standard PLC analog input card will not power the internal sensor circuits and will yield no signal output.\u003c\/p\u003e\n\u003ch3\u003eQ2: What specific field benefit does the -CN suffix provide for this accelerometer model?\u003c\/h3\u003e\n\u003cp\u003eA2: The -CN suffix certifies that the accelerometer carries local hazardous area compliance approvals for explosion-proof and intrinsically safe zones. This allows plant engineers to safely mount the transducer inside high-risk areas, like oil-gas processing units or chemical plants, without voiding insurance coverage or safety regulations.\u003c\/p\u003e\n\u003ch3\u003eQ3: Why does my vibration signal clip or drop out at higher machine velocities?\u003c\/h3\u003e\n\u003cp\u003eA3: Signal clipping usually indicates either a loose mounting stud or a physical acceleration level that exceeds the sensor's 50g operational ceiling. Check that the mounting stud is torqued to exactly 4.5 N·m and verify that the mounting surface is flat. If the machine's actual high-frequency impact energy exceeds 50g, you must swap the sensor for a lower-sensitivity, higher-range alternative.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":45518868349101,"sku":"330425-02-CN","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0733\/1613\/9181\/files\/bently-nevada-330425-02-cn-accelerometeracceleration-transducers-hraj1anqffy.jpg?v=1766980594","url":"https:\/\/www.maxwellplc.com\/products\/bently-nevada-330425-02-cn-piezoelectric-accelerometer-acceleration-transducer","provider":"Maxwell PLC Ltd","version":"1.0","type":"link"}