{"product_id":"bently-nevada-22810-00-0610-02-8-mm-proximity-probe","title":"Bently Nevada 22810-00-0610-02 8 mm Proximity Probe","description":"\u003cp\u003eThe\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003eBently Nevada 22810-00-0610-02\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eserves as the primary\u003cspan\u003e \u003c\/span\u003e\u003cstrong\u003e22810\u003c\/strong\u003e\u003cspan\u003e \u003c\/span\u003eProximity Probe utilized to execute non-contact shaft vibration and displacement monitoring across Bently Nevada TSI platforms. The probe assembly produces eddy-current output signals proportional to shaft movement and radial position variation within rotating machinery monitoring circuits.\u003c\/p\u003e\n\u003ch3\u003eHardware Specifications\u003c\/h3\u003e\n\u003ctable class=\"w-fit min-w-(--thread-content-width)\"\u003e\n\u003cthead\u003e\n\u003ctr class=\"firstRow\"\u003e\n\u003cth class=\"last:pe-10\"\u003eParameter\u003c\/th\u003e\n\u003cth class=\"last:pe-10\"\u003eSpecification\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003e22810-00-0610-02\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBrand\u003c\/td\u003e\n\u003ctd\u003eBently Nevada\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProduct Type\u003c\/td\u003e\n\u003ctd\u003eProximity Probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSeries\u003c\/td\u003e\n\u003ctd\u003e8 mm Eddy-Current Probe System\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOrigin\u003c\/td\u003e\n\u003ctd\u003eUSA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eApprox. 0.35 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eShipping Dimensions\u003c\/td\u003e\n\u003ctd\u003eApprox. 24 cm x 18 cm x 5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOperating Temp\u003c\/td\u003e\n\u003ctd\u003e-35 deg C to +177 deg C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower Consumption\u003c\/td\u003e\n\u003ctd\u003ePassive sensing device\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe Diameter\u003c\/td\u003e\n\u003ctd\u003e8 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMeasurement Principle\u003c\/td\u003e\n\u003ctd\u003eEddy-current non-contact sensing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eOutput Signal\u003c\/td\u003e\n\u003ctd\u003eDynamic vibration and static gap voltage\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable Type\u003c\/td\u003e\n\u003ctd\u003eShielded integral coaxial cable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnector Configuration\u003c\/td\u003e\n\u003ctd\u003eCoaxial signal connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting Method\u003c\/td\u003e\n\u003ctd\u003eThreaded body installation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTarget Material\u003c\/td\u003e\n\u003ctd\u003eElectrically conductive shaft surfaces\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eEddy-Current Probe Scaling and Rotor Dynamics\u003c\/h3\u003e\n\u003cp\u003eThe probe assembly functions as part of a calibrated transducer loop consisting of probe, extension cable, and driver electronics. Eddy-current probe scaling is dependent on matched system components and controlled cable impedance characteristics. Alteration of cable length or connector substitution may affect linearity and signal calibration.\u003c\/p\u003e\n\u003cp\u003eRotor dynamic monitoring applications use the transducer output to identify shaft eccentricity, imbalance response, and transient vibration behavior during startup and coastdown conditions. Gap voltage validation procedures typically target approximately -10 VDC during initial probe positioning and shaft centerline alignment verification.\u003c\/p\u003e\n\u003ch3\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cp\u003eQ: Can the 22810-00-0610-02 probe operate independently without a driver module?\u003cbr\u003eA: No. The probe requires compatible proximitor or driver electronics to convert the raw eddy-current signal into calibrated output measurements.\u003c\/p\u003e\n\u003cp\u003eQ: Does the probe require physical contact with the shaft surface?\u003cbr\u003eA: No. The sensing method is fully non-contact and operates through an electromagnetic field generated at the probe tip.\u003c\/p\u003e\n\u003cp\u003eQ: Can field technicians splice or extend the probe cable?\u003cbr\u003eA: Cable modification is not recommended because impedance changes may alter transducer calibration and signal response characteristics.\u003c\/p\u003e\n\u003cp\u003eQ: What installation condition commonly affects signal stability?\u003cbr\u003eA: Improper shield grounding, close routing near high-current conductors, or excessive connector contamination may introduce electrical noise into the measurement channel.\u003c\/p\u003e\n\u003cp\u003eQ: Is the probe compatible with hot-swap replacement procedures?\u003cbr\u003eA: Probe replacement should be completed with associated monitoring channels inhibited or de-energized to prevent false alarm conditions.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eField Installation Guidelines\u003c\/h3\u003e\n\u003cp\u003eVerify threaded probe engagement before shaft rotation. Insufficient mounting depth may permit probe movement during machine vibration events.\u003c\/p\u003e\n\u003cp\u003eMaintain separation between probe cables and motor feeder circuits, relay coils, or variable frequency drive output wiring to reduce electromagnetic interference.\u003c\/p\u003e\n\u003cp\u003eDo not sharply bend the coaxial cable near the probe body or connector transition area. Excessive bending stress may damage internal shielding continuity.\u003c\/p\u003e\n\u003cp\u003eInspect probe tip condition before installation. Metallic debris or surface contamination may affect gap voltage stability and vibration waveform quality.\u003c\/p\u003e\n\u003cp\u003eApply shield grounding practices according to the associated Bently Nevada monitoring system documentation to reduce ground loop effects.\u003c\/p\u003e","brand":"Bently Nevada","offers":[{"title":"Default Title","offer_id":45518866874541,"sku":"22810-00-0610-02","price":99.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0733\/1613\/9181\/files\/bently-nevada-22810-00-0610-02-8mm-proximity-probe-sudennv305y.jpg?v=1766980549","url":"https:\/\/www.maxwellplc.com\/products\/bently-nevada-22810-00-0610-02-8-mm-proximity-probe","provider":"Maxwell PLC Ltd","version":"1.0","type":"link"}